PressurePro is a tire pressure and temperature monitoring system that uses advanced technology. PressurePro provides real time tire performance readings and alerts that are communicated via networks to an onboard display and a central monitoring station from the vehicle and/or trailer tires.
The pressure sensor is easy to install and there is no need to dismount the tire. Simply screw the sensor on the valve stem.
PressurePro Benefits
The PressurePro Features
- Simple to fit, program and maintain.
- Fitted to the end of the valve stem or specific SensorSpud© dual headed wheel spuds
- Weighs 17 grams, usually less than the tire is out of balance
- Checks the pressure every 7 seconds
- Has alerts @ 12.5% & 25% under set pressure as well as 24% (adjustable) for over pressure
- Uses audio visual alerts but can be enabled to provide SMS, email, or other electronic alerts
Control Risk and Reduce Loss
Why is the first low pressure alert 12.5% below the correct cold pressure?
A tire running at 10% below its specified pressure:
- will wear at a 10% faster rate
- the rolling resistance increases so fuel consumption rises
- contact pressure is reduced 10%
- traction is affected increasing stopping distances
Safety is Compromised!
At 20% under set pressure the tire will wear 25% faster than at the correct pressure, the danger of a tire failure increases exponentially, the risk of a safety related incident increases.
Client Testimonials
How PressurePro Works
PressurePro 10 Wheel TPMS Monitor
Common uses
Consumer Vehicles, Light Trucks, Buses, Emergency Equipment, Straight or Box Trucks, Ag Equipment, Dump and Work Trucks, Heavy Duty and Mining Equipment
Description
PressurePro’s Pulse 10 Wheel Monitor allows users to monitor up to 34 wheel positions.
Built in Data Logging capabilities can log up to 45 days of tire stamped pressure and temperature information that can be downloaded to PressurePro’s Pulse free management software, or to an outside software platform. These capabilities allow you to track and recognize tire performance trends and take your tire maintenance program from reactive to proactive. Further, RS232 proficiency allows tethering and communication capabilities to other technology devices.
General Information
PressurePro’s Pulse Wheel Monitor is capable of reading pressures from 10 psi to 250 psi, are RS232 capable, and can display pressures in PSI, BAR or kPa. The Monitor also features two low pressure alert levels (at 12.5% and 25% drops), a user settable upper high pressure alert (adjustable from 10% to 45%) and a high temperature alert to warn drivers when temperatures reach 194°F. PressurePro’s Pulse Wheel Monitor also has self-diagnostic tests, allow simple installation and provide drivers with real time tire performance information whether parked or on the road.
Equipment and Accessories
PressurePro Tire Valve Stem Monitors – The Easy Simple Solution to Tire Management
PressurePro’s comprehensive line of ‘American Made’, Tire Pressure Monitoring Systems provides customers with the tools needed to add savings, safety and efficiencies to travel and fleet operations by providing real-time tire pressure and temperature monitoring. Readings and alerts as well as advanced monitoring options including data logging, drop-and-hook applications, remote monitoring, custom alerts and fully integrated solutions with leading Telematics providers, PressurePro remains the Best in TPMS.
10 WHEEL MONITOR (Part #ALTGPM10)
- Monitors 1 to 10 wheel positions
- Dimensions, Weight, Power = 6.5”W x 3.0”H x 0.5”D, 4 ounces, 12VDC
- Use on Auto, SUV, Heavy Equip, Ag, Bus, Truck
- Communicates (real time) via RS232 to a serial port
- Data Logging capabilities Antenna and power cord required – sold separately
UNIVERSAL INTELLIGENT REPEATER (Part #URA16)
- Monitors up to 16 wheel positions
- No user interface for Drop & Hook or Programming function
- Communicates with all trucking networks including J1587, J1939, CAN
- Transfers data over trailer network to Tractor J1939 or J1708 network
- Deutsch power cord & 7” Antenna Required – sold separately
INTELLIGENT “DROP & HOOK” MONITOR (Part #ITMA16)
- Monitors 1 to 64 wheel positions (16 on Tractor, 16 per trailer, up to 3 trailers)
- Dimensions, Weight, Power = 6.5”W x 3.0”H x 0.5”D, 4 ounces, 12/24VDC
- For use with – Tractor/Trailer(s) for “Drop & Hook” applications
- Communicates with J1587 Intelligent Repeaters over the J2497/ABS Network
- Transfers data from J2497 network to Tractor J1708 network
- Antenna and power cord required – sold separately
J1939 INTELLIGENT GATEWAY (Part #GWA16)
- Monitors up to 16 tires each on tractor/9 trailers/dollies – (160 tires total)
- No user interface for Drop & Hook or Programming function
- Communicates with Universal Repeater over all truck networks
- Transfers data from trailer network to Tractor J1939 network
- Deutsch power cord & Cabled Antenna Kit required – sold separately
16 WHEEL MONITOR (Part #RVGPM16)
- Monitors 1 to 16 wheel positions (capable of reading primary and tow vehicle)
- Dimensions and Weight = 6.5”W x 3.0”H x 0.5”D, 4 ounces, 12VDC
- Use with RV, Bus, 5th Wheel, all Trailers (boat, motorcycle, snowmobile)
- Communicates (real time) via RS232 to a serial port for fleet applications
- Data Logging capabilities
- Antenna and power cord required – sold separately
34 WHEEL MONITOR (Part #HDGPM34)
- Monitors 1 to 34 wheel positions – (capable of reading primary and tow vehicle)
- Dimensions and Weight = 6.5”W x 3.0”H x 0.5”D, 4 ounces, 12VDC
- Use with – Truck, Tractor/Trailer, Off Road (Mining), 5th Wheel
- Communicates (real time) via RS232 to a serial port for fleet applications
- Data Logging capabilities
- Antenna and power cord required – sold separately
INTELLIGENT BRIDGE (Part #BRIDGE16)
- Monitors up to 16 tires each on tractor/3 trailers/dollies; 64 tires total
- No user interface for Drop & Hook or Programming function
- Communicates with J1587 Intelligent Repeaters over the J2497 Network
- Transfers data from J2497 network to Tractor J1708 network
- Molex Power Cord & Cabled Antenna Kit required – sold separately
INTELLIGENT PROGRAMMING MONITOR (Part #IPM)
- Programming (display only) Monitor – cannot receive transmissions directly
- Dimensions, Weight, Power = 6.5”W x 3.0”H x 0.5”D, 4 ounces, 12/24VDC
- Used only for programming Intelligent product or as a pass through display when used in conjunction with J1939 Gateway
- Antenna and power cord required – sold separately
Specifications and Information
- Operating frequency = 433.92 MHz FM
- Temperature range: -40°C to +150C (-40°F to +302°F)
- Sensor batteries are internal, non-rechargeable/not replaceable
- Sensor pressure range = 8 to 299 psi (55 to 1999 kPa, 1 to 20.3 BAR)
- Accuracy = +/- 3% range up to 120 psi, +/- 5% 120 psi and higher
INDUSTRIAL SENSOR (Part #APS1-IND)
- For use with large bore (industrial) valve stems
- Weight – .7 oz (19 grams) / Dimensions: 1.11” D x 1.02” H
- Effective signal range – line of sight – 300 ft. – 433.92 MHz
- Robust electronics for industrial applications
SENSOR (Part # APS1)
- For use on standard valve stems
- Weight – .6 oz (17 grams) and Dimensions: 1.11” D x 1.01” H
- Effective signal range – line of sight – 300 ft. – 433.92 MHz
FIXED END POWER CORD (Part #AAPC1)
- Connects Monitor to 12-volt power outlet (accessory outlet in vehicle)
- 8 ft cord
STRIPPED END/HARD WIRE POWER CORD (Part #AAPC3)
- Hard wire to a 12-volt power source to power Monitor
- 8 ft cord
24/12 VOLT FIXED END POWER CORD (Part #AAPC5)
- Converts power from 24V (vehicle) to 12V (PressurePro Monitor)
- 8 ft cord
AC/DC WALL PLUG-IN KIT (Part #AAPACDC)
- Allows conversion of 110V AC to 12V DC on PressurePro monitor
- Kit includes 8 ft power cord and AC/DC converter
- Power cord powers Monitors and Echo Repeater
RS232 FIXED END POWER/DATA CORD (Part #ACPC7)
- Connects to 12V power source
- RS232 data cord required for downloading data from Monitor
- Utilizes DB9 connector for downloading to a computer serial port
24/12 RS232 FIXED END POWER/DATA CORD (Part #AAPC9)
- Connects to 24V or 12V power source
- RS232 data cord required for downloading data from Monitor
- Utilizes DB9 connector for downloading to a computer serial port
MOLEX POWER CORD (Part #AAPC11)
- Use with Intelligent Repeaters and BRIDGES
- Jacketed, 5-wire, 10 foot power/data cord
- Molex connector on one end / stripped end for connection to vehicle network
- Supports Open Collector function. Wired for J2497 and J1708 networks
MOLEX T-BREAKOUT CORD (Part #AAPC14)
- Use with Intelligent Repeater on trailers/dollies
- Jacketed, 2-wire, 8-foot power/data cord
- Molex connector on one end/T-Breakout on other for easy link to vehicle network
- T-Breakout attaches between the male/shroud of the Weather Pack connector of the standard ABS harness (no splicing necessary)
DEUTSCH END T-BREAKOUT CORD (Part #AAPC21)
- Use with Universal Repeater on trailers/dollies
- Jacketed, 3-wire, 8 foot power/data cord
- Deutsch connector on one end/T-Breakout on other for easy link to vehicle network
- T-Breakout attaches between the male/shroud of the Weather Pack connector of the standard ABS harness (no splicing necessary)
DEUTSCH END BLUNT CUT POWER CORD (Part #AAPC24)
- Use with Universal Repeater, Gateway, and Bridge
- Jacketed, 8-wire, 3 foot power/data cord
- Deutsch connector on one end / stripped end for connection to vehicle network
DEUTSCH END 9 PIN T-BREAKOUT CORD (Part #AAPC25)
- Use with Gateway
- Jacketed, 8-wire, 3 foot, power/data cord
- Deutsch connector on one end/T-Breakout on other for easy link to vehicle network
- 9 Pin T-Breakout attaches to Deutsch 9-pin diagnostic port
CABLED ANTENNA KIT (Part #ABPCA-Kit)
- Use with all Monitors – SMA end to Monitor, TNC end to antenna
- Includes: 35 ft coax cable, SMA & TNC connectors, straight wire whip antenna and mounting bracket for securing cable (includes two 1.25” self tapping screws)
- Bracket also sold separately as replacement part (Part #CAB, MSRP $5)
ECHO REPEATER (Part #ABPER)
- Telescoping dipole antennae included
- Velcro strips for mounting in vehicle included
- For use as a signal booster on mid-to large vehicles
- 12V Plug-in Power Cord or 110 Wall plug-in sold separately
STRAIGHT WIRE WHIP ANTENNA – 7 INCH (Part #AAP08)
- Use on Intelligent Repeater
- Sold separately as replacement part for Cabled Antenna Kit
MONOPOLE ANTENNA – 3.5 INCH (Part #ABPPMA)
- Use on SMA connector on Monitor (required if not using cabled antenna kit)
TNC ANTENNA ADAPTER (Part #AAP15)
- Antenna adapter for 3.5” SMA antenna when using with TNC connection on Repeater or if connecting to end of 35’ coax cable.
SENSOR LOCK KIT (Part #LNK)
- Includes 1 wrench and 10 nuts
- Additional nuts available at .50 cents per nut
VISOR CLIP/SUCTION CUPS (Part #AAPVC)
- Fits on Monitor – clips onto visor or suctions to window
- 2 clips per set
RAM MOUNT – (for mounting Monitor) (Part #AAP11)
- Ram Mount with 2.5” arm and 2 knuckle end plates – allows mounting in vehicle
- Total length and weight: 4” and 6.6 oz
RAM MOUNT MOUNTING PAD (Part #AAP13)
- 2.43” Diameter double stick mounting pad, sticks to all non-porous surfaces
COMBO RAM MOUNT (with) SUCTION CUP (Part #AAP14)
- Ram Mount and Suction Cup Combination
- Comes with suction cup at one end and regular round mount on the other end
RAM MOUNT SUCTION CUP ATTACHMENT (Part #AAP12)
- Suction cup attaches to windows, metal dashes and non-porous surfaces
- Power suction lever for secure fastening – Length:3.25” / Weight: 3.6 oz
VISOR CLIP DASH MOUNT (Part #AAP16)
- ‘Hybrid’ version of the Visor Clip Kit for an additional mounting option
- Visor Clip ‘legs’ attach directly to back of Monitor
- Mount can be screwed directly to mounting surface
SENSOR INSTALLATION TOOL (Part #AAP18)
- Plastic tool to install Sensors on the inside dual valve stem
- 12” handle easily reaches those hard to reach inside dual valve stems.
- Sensor seats firmly in end of tool but releases when sensor is snugly on stem
SENSOR SEAL/INSTALLATION TOOL KIT (Part #AAP21)
- Included – ten (10) Sensor seals and one (1) seal installation tool
- Allows secure installation of seal replacements into Sensor
T-VALVE – SUPER LARGE BORE STEM (Part #AAP24)
- For utilization on super large bore valve stems, allows air filling while Sensor is installed
- One side super large bore and large bore on other
- Main valve installs directly into rim or onto an existing super large bore stem
T-VALVE – LARGE BORE STEM (Part #AAP22)
- For utilization on large bore valve stems, allows air filling while Sensor is installed
T-VALVE STEM (Part #AAP20)
- For utilization on regular valve stems, allows air filling while Sensor is installed
HOOK & LOOP PADS (for mounting Monitor and Echo Repeater) (Part #AAP3)
- Two velcro strips included with purchase of Monitors and Echo Repeater